ADC AD-24 Installationshandbuch

American Dryer Corporation88 Currant RoadFall River MA 02720-4781 USATelephone: (508) 678-9000 / Fax: (508) 678-9447e-mail: [email protected]

6AntiwrinkleThis program selection helps keep permanent press items wrinkle free, when they are not removed from thedryer promptly at the end of the d

7SECTION IIINSTALLATION PROCEDURESA. INSTALLATIONThe dryer is mounted on a skid by four (4) bolts. The front two (2) bolts are located on the floor

8CAUTION: This dryer produces combustible lint and must be exhausted to the outdoors. Every 6months, inspect the exhaust ducting and remove any lint

9F. COMMON MAIN DUCTWhen individual exhaust is impossible, a common main duct may be used. However, strict attention must begiven to the constructio

10H. GAS DRYERSALL dryers are provided with 1/2” gas lines. Consult your local gas supplier for correct line size and pressure.The built in regulato

11An impulse trap and filter should be installed at each dryer. After 1 or 2 days of operation, the followingmaintenance should be performed:1. Press

12SECTION IIIL.E.D. DISPLAY AND CODESACOn Accumulative CoinAdrt Maximum Auto Dryness TimeAFAt Amount For Additional TimeAGt Active Antiwrinkle Guard T

13SECTION IVOPERATING INSTRUCTIONSNOTE: Unless otherwise specified at the time of ordering, the Phase 3 microprocessor controller(computer) has been p

143. Select temperature by pushing “HI TEMP,” “LO TEMP,” or “PERM PRESS.” The dryer will start, thelight emitting diode (L.E.D.) display will read th

15SECTION VPROGRAM SELECTIONSNOTE: Programs are stored in the computer memory and are cataloged as program locations (PL).Temperature Display ModeBy c

Retain This Manual In A Safe Place For Future ReferenceAmerican Dryer Corporation products embody advanced concepts in engineering, design, and safety

16At the end of the drying cycle, the dryer will go into the cool down cycle for the time period programmed (PL04,PL06, or PL08) or until the temperat

17Bad Coin Lockout Status (bCLO)In this program status, the computer counts in milliseconds the amount of time required for a coin entry signal. Ifso

18Dual CoinIn the time accumulation mode, when using a dual coin acceptor, once the “Amount To Start” (“AtSt”) has beeninserted, the addition of a coi

19Accumulative Coin (ACOn)When this program mode (“ACOn”) is selected, additional time can only be achieved when the “Amount ForAdditional Time” (“AFA

20PL02 - Dryness Level (drYL)When in the automatic mode or free dry mode, the dryer will run until the preset level of dryness (Number ofAuto Peaks) h

21PL09 - Left Coin Slot Denomination (LCdE)In the case of a single coin acceptor, this program setting is determined by the value of the coin acceptor

22PL15 - Antiwrinkle Timing1. Guard Delay Time (GdLY)This program controls the dwell (stop) time and activation of the antiwrinkle “Guard On Time” (“G

23SECTION VIINTRODUCTION TO PROGRAMMINGALL programming is done through the keyboard (touch pad) selection buttons on the front of the control panel.To

24Display ReadsTo speed up, “Push” and “Hold In” LO Tempselection button.Display reads program locations and willadvance downward until LO Temp select

25SECTION VIIPROGRAMMINGA. TEMPERATURE DISPLAY MODEand/or(Close Program Switch)(Cycle In Progress)(Close Program Switch)(Open Basket/Tumbler Door - D

IMPORTANTYOU MUST DISCONNECT AND LOCKOUT THE ELECTRIC SUPPLY AND THE GASSUPPLY OR THE STEAM SUPPLY BEFORE ANY COVERS OR GUARDS AREREMOVED FROM THE MAC

26B. RIGHT COIN COUNT (rCC)and/or(Close Program Switch)(Wait 3-Seconds)(To Clear Coin Count)(No Cycle In Progress)(Coin Count Cleared)25FILL70ºFHI TE

27C. LEFT COIN COUNT (LCC)(Open program switch [PS] to exit out of display mode)and/or(Close Program Switch)(Wait 3-Seconds)(To Clear Coin Count)(No

28D. PROGRAM LOCATION 01 (PL01)and/or(Close Program Switch)oror(No Cycle In Progress)25FILL75ºFPERM PRESSPL01ºCELºFArHI TEMPLO TEMPLO TEMP HI TEMPºCE

29ororornGrd GrdHI TEMPLO TEMPHI TEMPLO TEMPGrd nGrdPERM PRESSnbUZbUZLO TEMP HI TEMPLO TEMP HI TEMPbUZ nbUZPERM PRESSFrEECoinLO TEMPLO TEMP HI TEMPHI

30ororornFLS FLSHI TEMPLO TEMP HI TEMPLO TEMPFLS nFLSPERM PRESSFILLHI TEMPLO TEMPAtStAtStHI TEMPLO TEMPFILLPERM PRESSbCLOHI TEMPLO TEMPbCrSbCrSHI TEMP

31orACOnAtInAtInACOnPL02LO TEMP HI TEMP LO TEMP HI TEMPPERM PRESS

32E. PROGRAM LOCATION 02 (PL02)Number of Auto Peaks (Dryness Level)Summary: The dryness level is programmable from a minimum of 1 to a maximum of 99.

33F. PROGRAM LOCATION 03 (PL03)HI tempSummary: HI temp is programmable from a minimum of 100º F (38º C) to a maximum of 190º F (88º C) in ten-degree

34G. PROGRAM LOCATION 04 (PL04)HI Temp Cool Down Temperature/TimeSummary: Cool down temperature is programmable from a minimum of 100º F (38º C) to a

35H. PROGRAM LOCATION 05 (PL05)LO tempSummary: LO temp is programmable from a minimum of 100º F (38º C) to a maximum of 190º F(88º C) in ten-degree i

WARNINGThe dryer must never be operated with any of the back guards, outer tops, or servicepanels removed. PERSONAL INJURY OR FIRE COULD RESULT.IMPOR

36I. PROGRAM LOCATION 06 (PL06)LO Temp Cool Down Temperature/TimeSummary: Cool down temperature is programmable from a minimum of 100º F (38º C) to a

37J. PROGRAM LOCATION 07 (PL07)Perm Press TemperatureSummary: Perm Press is programmable from a minimum of 100º F (38º C) to a maximum of 190º F(88º

38K. PROGRAM LOCATION 08 (PL08)Perm Press Cool Down Temperature/TimeSummary: Cool down temperature is programmable from a minimum of 100º F (38º C) t

39L. PROGRAM LOCATION 09 (PL09)Left Coin DenominationSummary: The left coin denomination is programmable from 1 to 9999.(Wait 3-Seconds)(“Hold In” to

40M. PROGRAM LOCATION 10 (PL10)Right Coin DenominationSummary: The right coin denomination is programmable from 1 to 9999.(Wait 3-Seconds)(“Hold In”

41N. PROGRAM LOCATION 11 (PL11)Time Per Left CoinSummary: The time per left coin is programmable from 1 to 99 minutes.(Wait 3-Seconds)(“Hold In” to A

42O. PROGRAM LOCATION 12 (PL12)Amount To StartSummary: The amount to start is programmable from 1 to 9999.(Wait 3-Seconds)(“Hold In” to Accelerate)(“

43P. PROGRAM LOCATION 13 (PL13)Coin Accumulation Minimum Amount for More TimeSummary: The amount for additional time is programmable from 1 to 9999.(

44Q. PROGRAM LOCATION 14 (PL14)Maximum Time for Auto DrySummary: The maximum auto dryness time is programmable from 1 to 99 minutes.(Wait 3-Seconds)(

45R. PROGRAM LOCATION 15 (PL15)Antiwrinkle TimingSummary: Guard delay time is programmable from 1 to 9 minutes. Guard on time is programmable from 1

SECTION IINTRODUCTION... 4Phase 3 Features ...

46S. PROGRAM LOCATION 16 (PL16)Maximum Active Antiwrinkle TimeSummary: The maximum active guard time is programmable from 1 to 99 minutes.(Wait 3-Sec

47SECTION VIIIFACTORY PRESET PROGRAMSUnless otherwise specified at the time of ordering, the Phase 3 microprocessor controller (computer) has beenprep

48Single Coin OnlyPL01ºFArtInEGrdbUZCoinFLSbCrSAtIn Temperature in Fahrenheit Timed mode Antiwrinkle guard on Antiwrinkle guard buzzer (tone) on Coin(

49SECTION IXNON-COIN COMPUTER DRYERNon-Coin FeaturesAutomatic OperationThe user selects fabric and level of dryness desired. The dryer automatically

50Non-Coin Computer Dip Switch FeaturesThe dip switch (refer to the illustration below) is an 8-position red and white SPST switch mounted on theback

51Switch #8 - When the computer is being programmed in the automatic mode, a dryness level of 1 through 9must be selected. In some cases, a dryness l

52B. AUTOMATIC ONLY (NON-REVERSING DRYERS)Dip switch settings - Switch #1 - open Switch #2 - closedSwitch #3 - closedSwitch #4 - openSwitch #5 - clo

53D. AUTOMATIC/MANUAL PROGRAM SELECTABLE(“MANUAL” SELECTED, NON-REVERSING DRYERS)Dip switch settings - Switch #1 - open Switch #2 - closedSwitch #3

54a. “Auto” selected - follow steps 1 through 4 under “Auto Only” instructions of Section B. After completingstep 4, display will show “Sr_.”1) Press

55SECTION XSERVICE/PARTS INFORMATIONA. SERVICE1. Service must be performed by a qualified trained technician, service agency, or gas supplier. If se

Flash Display Status (FLS) ... 16Bad Coin Lo

56SECTION XIREPLACEMENT PARTS LISTNOTE: The above illustration may not depict your particular dryer exactly. This illustration is acomposite of the v

57Additional Parts Available But Not IllustratedPart No. Qty. Description136052 2 4-Amp Fuse122800 1 Microprocessor Pin Extractor Tool137056 1 or 2 Op

58SECTION XIIWARRANTY INFORMATIONA. RETURNING WARRANTY CARDS1. Before any dryer leaves the ADC factory test area, a warranty card is placed on the ba

592. Each part must be tagged with the following information:a.Model number and serial number of the dryer from which part was removed.b. Nature of fa

60SECTION XIIIROUTINE MAINTENANCEA. CLEANINGA program and/or schedule should be established for periodic inspection, cleaning, and removal of lint fr

616 MONTHSInspect and remove lint accumulation in customer furnished exhaust ductwork system. Clean lint/dust accumulationfrom between fins of steam

62SECTION XIVTROUBLESHOOTINGIMPORTANT: YOU MUST DISCONNECT AND LOCKOUT THE ELECTRIC SUPPLYAND THE GAS SUPPLY OR THE STEAM SUPPLY BEFORE ANYCOVERS OR G

63C. The dryer starts, but the heating unit is not running...1. The hi-limit thermostat is defective.2. The lint door is open.3. The sail switch is ou

644. An idler bearing or basket (tumbler) drive bearing failure.5. Motor air vents are blocked with lint.6. Defective motor.H. An excessive noise or v

65L. Display shows “dSFL”...1. Dryer sensor failed. Check if sensor is missing from holder.2. Check wires leading to sensor from connector to connect

SECTION VIIIFACTORY PRESET PROGRAMS ... 47Dual Coin ...

66SECTION XVOPTIONAL 9 VOLT BATTERY BACKUPDryers ordered from the factory with the 9 volt battery option (battery is not included) allows the micropro

67Notes ______________________________________________________________________________________________________________________________________________

ADC 112100 22 - 09/07/04-0

4SECTION IINTRODUCTIONThe Phase 3 computerized system is a fully programmable, highly sophisticated dryer control system. ADC hasdesigned the Phase 3

5Bad Coin LockoutEach coin entry is monitored. Should someone tamper with the coin acceptor or attempt to insert a foreignobject, the microprocessor